Chicco play yard manual

Fasten the four snaps on the corners of the bassinet. Pull the eight toggles through the loops on the playard. Place the remote control on its pocket on the bassinet. Place the mattress on the bassinet with the soft side up. Set up the changing table before installing it into the playard. Slide the metal poles through the sleeves on the sides of the changing table. Secure the metal end pieces to the metal poles. Make sure the spring buttons slide through the holes. Place the changing table on the playard with the metal arcs on the ends of the changing table facing down.

Place the netted pockets over the metal arcs on the ends of the changing table. Secure the Velcro on the pockets. Attach the buckles on each end of the changing table. Zip the zipper on the side of the playard to the changing table. Install four AA batteries on the electronic unit. Place the electronic unit on any corner of the playard. Avoid forcing it into place. Slide the switch to the left to turn the Lullaby Nitelite off. Slide one place to the right for the "Manual" setting to enable any mode for six minutes.

Slide another place to the right for the "Remote" setting to control the mode with the remote control. Slide completely to the right for the "Sound" setting, in which the music and vibration turn on with any sudden noise, such as when baby cries. Push the button with the wavy lines to turn on the vibration. Press the button with the light bulb to turn on the night light. Push the button with the music note to turn on the music. To use the remote control, point it to the unit and press the button for the desired setting.

The buttons are the same as those on the electronic unit. Slide the stuffed animals through the loops on the toy bar. Remove the mattress from the playard to install the toy bar. Insert the ends of the toy bar into each pocket on the corner of the mattress. Secure the snaps on the corners. Push the center of the toy bar down until it locks into position. Place the mattress with the toy bar on the floor for baby to play in. Pull each leg of the toy bar outwards to unlock it and fold it once the baby is done playing.

Remove the bassinet, changing table, mattress and electronic unit from the playard before packing it up. Turn the handle on the floor of the playard upwards and pull up to unlock the floor. Page 15 Setting Up the Playard Montage du parc 5. Install Mattress Pad, padded side up. Do not use playard without Mattress Pad and make sure to fold hook and loop strap underneath Mattress Pad. Ne pas utiliser le parc sans le matelas.

Page 16 Setting Up the Playard Montage du parc 6. Locate 4 Mattress Pad strap holes on the floor of the playard. Thread the 4 hook and loop straps through to the floor of the playard as shown. Page 17 Setting Up the Playard Montage du parc 7. Turn the playard on its side and pull the straps through the floor of the playard.

Thread the straps through the slot on the playard foot as shown. Pull hook and loop strap tight and then attach together to secure Mattress Pad. Do this for all 4 mattress corners. Pull up on mattress pad to make sure it is secure. Undo the hook and loop straps from the frame and remove Mattress Pad from playard.

Unfold the Bassinet sides as shown. Unfold the Bassinet ends over the playard frame. Fit the 4 corners of the Bassinet over the 4 corner Bassinet Supports on the Lullaby playard as shown 9C. Once the Bassinet is resting on the supports push down on the center joints on the long sides of the Bassinet 9D. This will secure the Bassinet into place. Push down on Bassinet to be sure it is secure.

Bassinet Supports 9B. Make sure enfant se trouve dans le parc. The Mattress Pad is slightly larger than the opening of the Bassinet.

Do not fully open the Mattress Pad. Insert the Mattress Pad on an angle and slide it towards the side opposite of you. Adjust the mattress to fit the opposite corners before inserting the end closest to you. When the Mattress Pad is fully inserted on the bottom push it firmly into place. This will make the sides taught and remove any slack in the fabric. Always check to make sure the hook and loop straps are folded under the Mattress Pad. Page 22 Attaching Parent Organizer Installation du panier Attach the Parent Organizer to the side top rail of the playard as shown.

Parent organizer can be attached to either side. For greater convenience, we recommend the side nearest to the changing table latches.

Make sure the tab is on the inside when assembling. Repeat for the other Changing Table Frame Side as shown. Do NOT Snap the other end onto the changer frame. Move to step 13 to install softgoods before finishing the changer frame assembly. Locate the fabric tabs along the outside of the Changing Pad. Thread the fabric tabs through the corresponding openings on the frame and pull the fabric tabs through. Flatten the fabric tabs out to secure them into place.

Repeat for both sides. Passer chaque attache en tissu dans l'ouverture correspondante du cadre, puis tirer. Locate the changing table receptacles on the side of the playard. Assemble the changing table by lining up the corners of the changing table frame with the corners of the playard. Press down until the changing table latches into the playard receptacles.

Pull up on changing table to check for attachment. Never use the changer on another surface or playard. Remove the changing table by pushing in on the release buttons and lifting up. The changing table can be stored by hanging on the Parent Organizer as shown. Always use on floor. Never use on any elevated surface. ONLY use the pad provided by Chicco.

NEVER place extra padding under or beside infant. Only use in Lullaby Dream when napper is properly attached to the installed bassinet. NEVER use napper in different product. NEVER use in contained areas e. NEVER use on a soft surface e. Always place child on back to sleep. NEVER leave child unattended. You are responsible to provide adult supervision when using your napper. Toujours utiliser le produit sur le sol. Page 31 Assembling Napper Assemblage de la couchette Unfold the Napper Frame and extend the Napper Frame Leg, making sure that the locking tab clicks into place.

Page 32 Assembling Napper Assemblage de la couchette On the back of the Napper Pad locate the zipper and unzip.

Slide the Napper Frame into the Napper Pad making sure the attachment clip fits through the opening on the top of the Napper Pad. Fold the fabric around the Napper Frame and re-zip the Napper Pad. Glisser le cadre de la couchette dans la housse. Page 33 Assembling Napper Assemblage de la couchette Install the Napper by lining up the attachment clip with the side of the playard and pressing the attachment clip down around the side of the playard.

Make sure the bottom edge of the Napper is resting on top of the Bassinet frame. Page 34 Assembling Napper Assemblage de la couchette To store Napper, pull out on locking tab and fold the frame leg down.

Then fold the Napper in half as shown. Ensuite, plier la couchette en deux. Page 35 Assembling Toy Mobile Assemblage du mobile Page 36 Assembling Toy Mobile Assemblage du mobile Page 37 Assembling Toy Mobile Assemblage du mobile Insert the knot at the end of the Toy Mobile canopy string through the opening at the top of the Toy Mobile Arm, as shown.

Pull on the fabric to secure the string. Page 38 Assembling Toy Mobile Assemblage du mobile Slide the Toy strap through the opening on one of the sides of the Toy Mobile. Fold the hook and loop strap together to secure the toy. Repeat for the remaining 2 Toys. Page 39 Assembling Toy Mobile Assemblage du mobile